代写program、代做Java/Python程序
COURSE WORK ASSESSMENT Lab B(Team A Students) -INDIVIDUAL
MODULE :Data communication and networking
OVERVIEW
In this assignment student will demonstrate their understanding of Wide Area Network setup
using ROUTER. Also an implementation of Dynamic host configuration server and dynamic
IP addresses to end devices.
WEIGHTING:10 %
SUBMITTED DATE:__________________________________________
Submission Mode: Online through Blackboard – Assessment: Lab B submission Link
LECTURER: Ms Latha Manian
Student Name:
Student ID:
Acknowledgement:
I certify that this assignment is my own work. It does not reproduce anyone
else’s work without proper acknowledgement.
Signed By: ____________________________________________________
Date: _________________________
th
–
MODE: FULL TIME
DUE DATE: 9 May 2025 11:59 PM
Weighting: 10% of the module
Instructions:
You’re given 2.5 hours to complete the task within Lab session.
Objective 1:
Connect two different networks: LAN Connection 1 to LAN Connection 2 using Router
Network 1:
Name the devices PC0 and PC1 as SamPC with Ipv4 address – 10.1.1.1 and DollyPC with Ipv4 address –
10.1.1.2 Ensure the subnetting mask is 255.0.0.0
Add switch(2960) and Router(ISR4331) with Gigabyte Ethernet adapter
Highlight the entire network with color yellow and Write Note to the network as LAN Connection1
Configure IP Address to the LAN Connection1 as 10.1.1.3 ( configure in the router-Gigabyte interface )
ON the port status in router
Set the Default gateway to both end devices as 10.1.1.3
Network 2:
Name the devices PC0 as NancyPC with Ipv4 address – 192.168.1.1 and PC1 as BeePC with Ipv4 address –
192.168.1.2. Ensure for Subnet mask as 255.255.255.0
Add switch(2960) to the same Router(ISR4331) with Gigabyte Ethernet adapter
Highlight the entire network with color green and Write Note to the network as LAN Connection2
Configure IP Address to the LAN Connection2 as 192.168.1.3 (configure in the router- Gigabyte interface),
ON the port status in router
Configure Default gateway address to both end devices as 192.168.1.3
Observation: Send data packets from LAN1(Sam PC) to LAN2(NancyPC) . The status should be successful in both
real time and simulation mode. From simulation mode take a picture(Image1) of successful status and attach to
the word file. Sample Image1 is given below.
Objective 2:
Assign dynamic IP address using DHCP to PC
Add server and Label it as PSBServer
Config PSBServer IP as 192.168.100.1
Add two switches
Add three PCs to the second switch
Connect all the devices as given : PSBServer - Switch0 – Switch1-PC0,PC1,PC3
Go to PSBServer and ON the DHCP Services
Write a script in Command Line Interface of swtich0 and switch1 to enable dynamic IP address configuration
Challenge: Observe all end devices configured with dynamic IP Address connected to switch1 .
Ping from PSBserver to PC0 and the PING should be successful (Image2). Image2 sample is given
below.
Write down the following script in switches
enable
config t
interface vlan 10
ip address 192.168.100.10 255.255.255.0
exit
Lab submission to Blackboard:
A Word file (Studentname-LabB-TeamA.Docx) with cover page. Include Objective 1 and Objective 2 answers in the word file.
Objective 1 : Image1 with discussion on whether the router device is required for sending packets for two different networks .
Proper Labelling and highlight colour are required for complete marks. - 5 Marks
Objective 2: Discuss in three lines on dynamic configuration of IP addresses and attach image2. - 5 Marks
Note: To avoid plagiarism , ensure that the lab work is your own work. Lecturer check students work for plagiarism.
*****************